ASME Code Standards for Pressure Vessels and Piping Engineering Practice Test

These questions are part of the practice quiz. Start practicing

• ANSI B36.10 refers to:
• What does a closed chilled water system require?
• What is the primary consequence of maintaining a higher vacuum in the condenser on turbine operation?
• PWHT primarily reduces which condition in materials?
• ASME B31.5 applies to which piping system?
• Fatigue evaluation in Division 2 uses which of the following data or methods?
• Where is a pressure relief valve required?
• Air receiver tank must be designed per which code?
• MAWP stands for which term?
• ASME B31.9 covers which category of piping?
• Category D weld joints are used in which seam areas?
• Which standard defines the dimensions for welded and seamless pipe?
• The ASME code symbol stamp 'U' indicates which of the following?
• ASME Section III applies to which type of components?
• Design by rule is primarily used in which ASME division?
• PWHT is used primarily to reduce what?
• In steam piping design, expansion devices help accommodate what?
• Cooling tower drift loss results in loss of which of the following?
• Which code primarily covers Process piping?
• The NBIC provides guidance for which activity related to pressure vessels?
• Which code covers gas transmission and distribution piping?
• What can flange rotation during pressurization result in?
• The MAWP is determined based on:
• Which organization publishes the ANSI/ASME B16.9 standard for wrought butt-welding fittings?
• Stress Intensification Factors (SIF) are applied in which type of analysis for piping?
• How is steam quality (dryness fraction) defined?
• Unified inch screw threads are defined by which standard?
• Hydrostatic test multiplier relative to MAWP adjusted, per Section VIII Div.1, is which option?
• Which code covers Power Piping systems?
• MAWP stands for which term?
• What does proper bolt preload in flange joints ensure?
• What is the practical effect of reducing joint efficiency on required thickness?
• What must an engineer do when re-rating a vessel to a higher pressure?
• Re-stamping of a pressure vessel in response to a MAWP change must be performed in accordance with which guide?
• What should be done if total steam demand exceeds boiler rating?
• ASME B16.34 applies to?
• How does an alteration differ from a repair?
• For power boilers, the maximum allowable pressure accumulation with a single safety valve is typically:
• What does external pressure design use?
• Which factors must be determined when using external pressure charts?
• A refrigeration receiver used in industrial chillers must be designed in accordance with which ASME section?
• Combined stress evaluation in piping is typically based on which theory or theories?
• Where is radiographic examination required?
• During fire exposure, allowable pressure accumulation may increase to what percentage?
• ANSI B16.11 applies to which components?
• Which parameter is used to account for weld and geometry discontinuities in piping fatigue analysis?
• What is the primary reason to install an expansion device in steam piping when line length grows?
• ANSI thread engagement requirements are designed to ensure which property of threaded connections?
• What is the primary purpose of PWHT (Post Weld Heat Treatment)?
• Which ASME code section specifically governs radiographic examination requirements for pressure boundary components?
• Allowable stress in ASME codes is typically based on which material property?
• ASME Section IX covers:
• Which ASME document would you consult for material specifications of pressure vessel components?
• External pressure charts require determination of which factors?
• Minimum Design Metal Temperature affects which requirement?
• Reinforcement area required for an opening must be at least twice the removed area. If removed area is 18 in^2, minimum reinforcement area is?
• Expansion stress range allowable is based on what?
• Category B weld joint refers to which kind of joint?
• What increases when new bottling machines are added?
• What is the effect on required wall thickness when pressure increases while S and E remain constant?
• The Stress Intensification Factor (SIF) affects which aspect of piping analysis?
• Which criterion is commonly identified with Von Mises theory, using distortion energy to predict yielding?
• If joint efficiency equals 1.0, how does the required thickness compare to a lower efficiency?
• Which parameter primarily determines the saturation temperature of steam?
• What must be considered for chilled water pump selection?
• The formula t = PR/SE is used to calculate which of the following?
• Why must head thinning during forming be considered in design?
• Final verification of MAWP must consider which factor?
• The 'U' stamp signifies construction under which ASME division?
• What is the significance of the critical point for water?
• ASME B31.9 covers which type of piping?
• Which theory is described as the distortion energy approach and is used to predict yielding under multi-axial loading?
• What is the result of maintaining a higher turbine inlet temperature?
• NPS refers to?
• What is the first verification step if the existing boiler MAWP is 12 bar and the new pasteurizer requires 10 bar steam?
• ASME Section I primarily applies to:
• ASME B16.5 covers which category of components?
• Hydrostatic testing primarily reveals?
• Which modification most effectively minimizes pressure drop in a long compressed air piping system?
• Minimum bolt stress ensures?
• What is the safety valve accumulation limit for a single device?
• What is the approximate critical pressure of water?
• When is code stamping applied?
• What joint efficiency does spot radiography provide?
• ASME Section VIII Division 1 applies to pressure vessels operating above which threshold?
• Under external pressure, what is the likely failure mode if the pipe wall is not sufficiently thick?
• The impact requirement is influenced by which temperature consideration?
• What does B16.25 specify?
• RT-1 indicates?
• Von Mises stress theory evaluates what kind of stress under what loading condition?
• Which reference provides the primary data for piping material allowable stresses?
• Which value corresponds to full radiography joint efficiency?
• What is required before performing a repair on a code-stamped pressure vessel?
• External pressure design aims to prevent buckling collapse.
• Full penetration welds are required for which type of joints?
• Which ASME section governs the design and construction of power boilers?
• How is allowable external pressure for thin-wall pipe subjected to vacuum determined?
• In design practice, which change to a pipe cross-section most directly increases resistance to buckling aside from material changes?
• Pipe schedule primarily indicates which physical property?
• The Tresca failure criterion is based on which stress measure?
• Division 2 differs from Division 1 in what way?
• What does ANSI B16.20 apply to?
• What happens to required thickness when increasing internal pressure while holding S and E constant?
• Which components are used to remove water from a compressed air system?
• What is the most critical responsibility of a Facility Engineer in utility integration?
• If a cooling system uses TR units, the total heat rejection is approximately TR multiplied by what factor?
• What is DN designation?
• The addition of more bottling machines impacts which of the following system loads in proportion to machine count?
• Which standard specifies requirements for pipe flanges and flanged fittings?
• Which expression represents the hoop stress in a thin-walled cylinder under internal pressure?
• Which statement about code stamping is true?
• Corrosion allowance is added to which quantity in piping design?
• Fatigue evaluation in Division 2 relies on which method?
• What does maintaining a high vacuum in the condenser improve?
• Which radiography method yields 0.90 joint efficiency?
• Which ASME code primarily covers process piping?
• LPG storage vessels are designed according to which code?
• What does adding a 500 TR chiller increase?
• The 'U' stamp indicates which type of vessel?
• What is the primary purpose of minimum bolt stress in gasketed joints?
• Which code addresses refrigeration piping?
• What does pipe schedule indicate?
• Bolt allowable stress decreases with which condition?
• What should be checked if cavitation is observed in a chilled water pump?
• When modifying steam piping, which code must the design comply with?
• ASME Section III is applicable to which of the following components?
• Which option correctly pairs Category A and Category B weld joints?
• ASME B36.10 is the standard for pipe dimensions of which material?
• ASME B36.19 covers the dimensions for which type of pipe?
• What does feedwater heating in regenerative cycles increase?
• In the context of facility integration, which three aspects are most critical for a Facility Engineer?
• The stress range equation in ASME B31.3 accounts for which stresses?
• What is the gasket factor 'm' used to determine in flange design?
• Pipe supports primarily prevent which of the following in a piping system?
• How is the shell thickness of a water-cooled chiller evaporator determined?
• NBIC guidelines primarily govern which aspect of vessel work?
• Why are expansion loops provided?
• The design factor in ASME B31.8 gas transmission piping is used for?
• What joint efficiency does full radiography provide?
• What is the difference between NPS and DN?
• ASME B16.47 covers which category of flanges?
• Division 2 fatigue curves are based on which type of data?
• What is the main cause of external pressure failure?
• In regenerative cycles, the heat used for feedwater heating is typically obtained from which source?
• Which option is a nondestructive examination method?
• What does ASME B31.8 cover?
• A modification to an LPG storage tank requires compliance with which code?
• Pressure-temperature derating accounts for what change in allowable stress?
• Where are allowable stress values for piping materials obtained from?
• Increasing which geometric property of a pipe increases elastic buckling resistance?
• How is required shell thickness for internal pressure calculated?
• RT-2 indicates?
• Maximum accumulation for a single safety valve?
• What is the typical E value if no RT is performed?
• What is important to prevent cavitation in pumps?
• Which factor governs the high-temperature design stress for superheater tubes?
• Allowable stress values for materials used in ASME design are found in which code part?
• Pneumatic testing pressure compared to hydrotest?
• Which design approach explains why Division 2 typically allows higher allowable stress than Division 1?
• Which standard covers welding and brazing qualifications?
• In piping practice, branch reinforcement calculations are typically performed under which standard code designation?
• How does a reheat Rankine cycle improve plant performance?
• Where are impact testing exemption curves found?
• Hydrostatic testing verifies two main aspects: leakage and structural integrity.
• MDMT primarily influences the need for which testing?
• Which code is applicable to LPG storage tank modifications?
• Which flange class has a higher rating than Class 600?
• Which standard defines flange pressure classes?
• UG-28 refers to which type of pressure in code?
• ANSI B1.1 defines standards for which thread type?
• Why is hydrostatic test pressure sometimes adjusted for temperature?
• A compressed air receiver tank is classified under which ASME section?
• What does cooling tower drift loss refer to?
• Which radiography method yields approximately 0.85 joint efficiency?
• What does MAWP stand for?
• ASME Section II Part D provides information on which topic?
• What is the design temperature?
• Minimum required thickness excludes which element?
• When is PWHT required?
• In Division 2, which design approach is employed that differs from Division 1?
• ASME Section IV applies to which equipment?
• Reinforcement limits around nozzles are defined by which zone?
• ANSI B16.47 covers which of the following?
• What primarily governs superheater tube design stress?
• ASME B31.4 covers which piping types?
• How does ASME Section VIII Div. 2 differ from Div. 1?
• When can a Code Case be used?
• What is the radiography joint efficiency for full radiography?
• Which value represents the radiography joint efficiency for full radiography?
• What is the minimum design pressure for ASME Section VIII?
• Code Case usage requires acceptance by which entity?
• Which statement about Class 300 flanges is true compared to Class 150?
• Hydrotest temperature must avoid which region to prevent brittle fracture?
• Hydrostatic test pressure per Section VIII Div.1 is:
• Which guideline governs nozzle reinforcement?
• Pipe schedule primarily affects which property?
• When is hydrostatic testing of a power boiler typically performed?
• Minimum bolt preload must overcome which combination in a bolted joint?
• What causes water hammer in HVAC piping systems?
• Relief valve set pressure must be equal to or less than which parameter?
• Category D weld joints typically involve?
• ASME B16.34 applies to?
• What must be installed if the steam line length is significantly increased?
• Non-destructive testing methods are standardized in which ASME Section?
• The Stress Intensification Factor is used in which type of analysis?
• In piping design, which code governs branch connection reinforcement calculations?
• The slenderness ratio of a piping component primarily influences which failure mode?
• What is the primary purpose of a gasket in a flange joint?
• NBIC primarily covers?
• Which standard governs flange pressure classes?
• Valve dimensions and pressure-temperature ratings are defined by which standard?
• If joint efficiency is reduced from 1.0 to 0.85, what happens to the required thickness?
• Which designation is used to indicate pipe size in metric units?
• Minimum bolt stress is primarily associated with maintaining what kind of seal?
• What must be considered for steam header expansion?
• Stress Intensification Factor is used in which analysis?
• External pressure design primarily prevents?
• Which change increases shell buckling resistance?
• Expansion in long chilled water piping is primarily used to accommodate what?
• ASME B16.5 governs which category of components?
• ASME B16.34 covers which aspects of valves?
• NPS and DN relate as what?
• Allowable external pressure is obtained from which source?
• What is the hydrotest pressure per UG-99?
• For Division 2, which design approach is associated with allowing higher allowable stress?
• Which device provides overpressure protection for a closed refrigerant vessel?
• ASME Section V covers which methods?
• Design pressure must be greater than or equal to which value?
• ASME B16.25 specifies the end preparation for which weld feature?
• ASME B16.25 specifies the end preparation for which welded joints?
• Piping under external pressure typically fails due to which phenomenon?
• Allowable stress values location in ASME code.
• What is the corrosion allowance?
• Under UG-99, hydrotest pressure is MAWP × ?
• What primarily affects the thermal efficiency of a steam power plant?
• Why is boiler blowdown performed?
• Which boiler component is used to recover heat from flue gases?
• When radiographic testing is not performed, what E value is used?
• What covers pressure vessels operating above 15 psig?
• SIF are used in which piping analysis?
• In gas piping design, the design factor primarily affects which calculation?
• Which statement is true regarding relief valve setting in relation to MAWP?
• Cooling tower capacity must be verified based on what?
• Division 2 design philosophy
• When increasing boiler firing rate, which subsystems must be verified?
• What is the minimum test pressure for boilers (Section I)?
• What does an 'R' Stamp signify in NBIC context?
• What is allowable stress typically based on?
• Which factor is used to determine the wall thickness in ANSI pipe schedules?
• In boiler systems, the economizer is classified as what?
• If joint efficiency decreases, what happens to the required shell thickness?
• During hydrostatic testing, the test temperature should be controlled to avoid what condition?
• B16.25 specifies what?
• Minimum Design Metal Temperature (MDMT) primarily affects which testing requirement?
• In relation to operating pressure, design pressure must be what?
• What primarily determines the required thickness of a steam drum under internal pressure?
• Division 2 fatigue analysis typically uses what data to generate curves?
• What is true about Class 300 flanges?
• UG-99 covers which nondestructive examination method?
• Category A weld joint refers to which kind of joint?
• What is the basis for ASME flange pressure Class 150 rating?
• LPG storage vessels are typically designed according to which code?
• Hydrostatic test pressure for pressure vessels per ASME VIII Div. 1 is generally equal to how many times the MAWP?
• Which code would you reference for power piping design and installation requirements?
• What is the longitudinal stress in a thin cylindrical shell under internal pressure?
• ANSI B16.5 standard specifies requirements for:
• Who commissions the Authorized Inspector (AI) for a vessel?
• According to Section VIII, what is the maximum set pressure for safety valves?
• What governs nozzle reinforcement?
• What does ANSI pipe schedule primarily define?
• Flange pressure-temperature rating generally behaves?
• How is thermal expansion in long chilled water pipelines primarily accommodated?
• In a thin-walled cylinder under internal pressure, which expression correctly represents the circumferential (hoop) stress?
• Which organization governs repairs and alterations of pressure vessels after service?
• The allowable external pressure depends on which factors?
• Which role is typically authorized to inspect after major modification?
• ASME B31.3 primarily covers:
• What covers refrigeration piping?
• What is the primary basis for sizing a closed expansion tank in chilled water systems?
• What does ASME Section V contain?
• ANSI B16.47 covers which of the following?
• Why is pneumatic testing risky?
• If MAWP changes due to alteration, what action is required?
• Which device in a compressed air system is primarily used to remove moisture from the air?
• How far does the reinforcement zone extend?
• If joint efficiency decreases, which design parameter is increased?
• If steam demand exceeds boiler capacity, what is the recommended action?
• ASME Data Report Form U-1A is used for which equipment category?
• Who must conduct inspection after major modification of a pressure vessel?
• Which code governs the design of an air receiver tank?
• How does Division 2 differ from Division 1 in approach to design?
• What does a vessel stamped with 'U' indicate?
• How is dryness fraction (steam quality) defined?
• Which standard provides dimensions for carbon steel pipes?
• Which parameter does not directly determine the saturation temperature?
• ANSI/ASME B16.9 covers which components?